Skip to content
AssetLoom
Interactive 3D preview (reduced-detail model, 25,108 triangles · 12 × 10 × 8.9 cm). The downloadable files are the full-resolution originals.

Description

A soft-edged desk dock for foldable phones. Your own MagSafe-style charging puck sits in a carrier that slides in a 45 degree dovetail channel in the backrest, so you can set it to where your phone's magnets are. The phone stands closed for charging, or open (tall or wide) for video and calls.

Sized from Apple's published iPhone Duo dimensions (closed 84.1 x 117.8 x 11.3 mm, open 164.6 x 117.8 x 5.2 mm). It also suits other MagSafe or Qi2 phones whose magnets sit 30 to 65 mm above the bottom edge. Not affiliated with or endorsed by Apple. No charger, puck or cable is included.

What's included (9 print files, STL + 3MF, in print orientation)

  • Dock in two cradles: bare (phones up to 12 mm thick) and case (up to 15 mm)
  • Puck carriers for the 25 W puck (55.5 x 4.5 mm) and the older 15 W puck (56.1 x 5.4 mm), each in a standard (0.3 mm) and a loose (0.4 mm) slide fit
  • Spacers 5, 10 and 20 mm, marked with 1, 2 and 4 dots, in both fits: stack them to set the puck centre anywhere from 30 to 65 mm above the cradle floor in 5 mm steps
  • A fit test: a slice of the dock channel, a standard and a loose slider slice, and pocket rings for both pucks, so you can check your printer before the long print
  • The .blend file and the Python generator that builds every part

Design details

  • Fluted back, rounded pebble base, and a backrest that leans 20 degrees and stops 37 mm below the top of the closed phone, so the camera area stays clear
  • The carrier's rim above the puck is lowered 3 mm, so a camera bump up to 2.5 mm deep clears it
  • The cable leaves the top of the carrier, drops through a 4 mm slit in the backrest (braided puck cables are about 2.4 to 3 mm), runs down a groove on the back and out through a channel in the base
  • Underneath: recesses for four 10 mm rubber bumpers, and three front pockets for 24 to 25 mm coins or M12 washers (about 80 g) for extra steadiness
  • Made for two colours: print the dock in one colour and the carrier and spacers in another

Print settings

  • 0.4 mm nozzle, 0.2 mm layers, no supports, print as supplied, XY compensation 0
  • PLA or PETG. Dock: 3 walls, 25 to 40 % infill. Carrier and spacers: 3 walls, 20 %
  • The dock fits a 180 x 180 mm bed

Please note

The phone in the previews is a generic mock-up at the published iPhone Duo size, and the puck and cable are render props. Apple doesn't publish where the Duo's magnets or camera bump sit, which is why the carrier slides and the backrest stays low. We only promise charging with the phone closed. Every fit was checked in software on the exported meshes: cradle widths, channel widths, slide gaps along the full travel, and pocket sizes. The dock has not yet been test-printed by us, which is why there are two fits and a fit test.

Technical details

Formats
STL, 3MF, BLEND
Software
Bambu Studio, PrusaSlicer, OrcaSlicer, Cura, Blender
Provenance
Procedural
AI training
prohibited
Watertight
Yes
Manifold
Yes
Print tested by creator
No
Printer type
fdm
Supports required
none
Dimensions (W×D×H mm)
dock 118 x 104 x 83.5; carriers 70 x 61 x 6.2; spacers 5/10/20 mm; fit test 125 x 130 x 10
Recommended print settings
0.4 mm nozzle, 0.2 mm layers, no supports, no scaling, XY compensation 0. PLA or PETG. Dock 3 walls, 25-40 % infill; carrier and spacers 3 walls, 20 %. Print the fit test first.

Version history

Latest version 1.0.2, released .

  1. 1.0.2

    Download tidy-up: removed internal build files

  2. 1.0.1

    File tidy-up: cleaner file metadata and notes; no changes to the models.

  3. 1.0.0

Reviews

Own this asset? Sign in to review it.

No reviews yet. Owners can share how the asset worked for them.

    Questions & comments

    Sign in to ask the creator a question.

    No questions yet. Ask about formats, compatibility or licensing.