Skip to content
AssetLoom
Interactive 3D preview (reduced-detail model, 58,942 triangles · 22 × 11 × 10 cm). The downloadable files are the full-resolution originals.

Description

A modern bedside dock that keeps your phone, watch and earbuds in one place. You fit your own chargers: a MagSafe-style (Qi2) puck for the phone and a round magnetic watch puck for the watch. Not affiliated with or endorsed by Apple or any phone, watch or earbud maker. No chargers or cables are included.

How it works

  • Phone: works like our Foldable Phone Charging Dock, sized for full-size phones: the puck sits in a carrier that slides in a 45 degree dovetail channel in a backrest leaning 20 degrees. Stack spacers (5, 10, 20 and 30 mm) under it to put the puck centre anywhere from 30 to 95 mm above the cradle floor, so it meets your phone's magnets.
  • Watch: a paddle leaning 12 degrees holds the watch on its side, band open, for the bedside clock view. The puck sits in a ring in a 6.5 mm deep socket. The rings are bored 27.6, 28.1 and 28.6 mm (S, M, L); reported watch puck sizes are about 27.5 to 28.1 mm across.
  • Earbuds: a 66 x 49 mm dish in front of the paddle holds the case (it holds it; it does not charge it).
  • Cables: each leaves the top of its puck, drops through a slit, runs down a groove on the back and leaves through a channel in the base.

What's included (10 print designs, each as STL and 3MF, in print orientation)

  • Dock with two phone cradles: bare (phones up to 12 mm thick) and case (up to 15 mm)
  • Phone puck carriers for 25 W pucks (reported about 55.5 x 4.5 mm) and older 15 W pucks (reported about 56.1 x 5.4 mm), each in a standard (0.3 mm) and a loose (0.4 mm) slide fit
  • Spacers 5, 10, 20 and 30 mm (marked with 1, 2, 4 and 6 dots), in both fits
  • Watch rings S, M and L plus two 1 mm shims for thinner pucks
  • A fit test with a channel slice, slider slices, pocket rings and an upright slice of the watch socket, so you can check your printer and your pucks before the long print
  • The .blend file

Design details

  • Rounded pebble base, fluted backs and flared feet in one design language, with the phone and watch leaning at different angles
  • Made for two colours: print the dock in one colour and the carrier, spacers and watch ring in another
  • Underneath: recesses for six 10 mm rubber bumpers and three pockets for 24 to 25 mm coins or M12 washers (about 55 to 70 g) for extra steadiness

Print settings

  • 0.4 mm nozzle, 0.2 mm layers, no supports, print as supplied, XY compensation 0
  • PLA or PETG, 3 walls, 20 to 30 % infill
  • The dock is 224 x 112 x 102 mm and needs a bed of at least 230 x 120 mm (fits 250 x 210 and 256 x 256 beds)

Please note

The phone, watch, earbud case, pucks and cables in the previews are generic mock-ups and render props. Watch puck sizes are not published by the makers, so the rings come in three sizes with shims and a fit test. Anything on your phone's back that sticks out more than 0.2 mm must start at least 101 mm above its bottom edge or sit beside the carrier. Lift the phone off by tilting it forward, as the carrier rests on its spacers. Every fit was checked in software on the exported meshes. The dock has not yet been test-printed by us, which is why there are two slide fits, three ring sizes and a fit test.

Technical details

Formats
STL, 3MF, BLEND
Software
Bambu Studio, PrusaSlicer, OrcaSlicer, Cura, Blender
Provenance
Procedural
AI training
prohibited
Watertight
Yes
Manifold
Yes
Print tested by creator
No
Printer type
fdm
Supports required
none
Dimensions (W×D×H mm)
dock 224 x 112 x 102.3; carriers 70 x 61 x 6.2; spacers 5/10/20/30 mm; watch rings 33.4 x 6; fit test 164 x 130 x 46
Recommended print settings
0.4 mm nozzle, 0.2 mm layers, no supports, no scaling, XY compensation 0. PLA or PETG, 3 walls, 20-30 % infill. Print the fit test first.

Reviews

Own this asset? Sign in to review it.

No reviews yet. Owners can share how the asset worked for them.

    Questions & comments

    Sign in to ask the creator a question.

    No questions yet. Ask about formats, compatibility or licensing.