Loading 3D preview…
Description
A clean, chunky stand set for every screen on your desk: three phone stands (55°, 65°, 75°) and two tablet stands (60°, 70°), each with a charging-cable notch and tunnel so you can charge while it stands. Fits devices up to 12 mm thick with a case.
What's included (5 models, STL + 3MF + 2 plates)
- Phone stands 55° / 65° / 75°, 72 mm wide
- Tablet stands 60° / 70°, 130 mm wide
- Plates: all three phone stands on one plate, both tablet stands on another
Features
- 13.5 mm device slot with a 9–11 mm front lip
- 14 mm cable notch through the ledge + tunnel out of the back (USB-C plug and boot clear it, verified)
- Wide footprint: the centre of gravity of a 165 mm phone / 250 mm tablet stays 25–50 mm inside the base
- Recesses for 10 mm rubber bumpers
Print settings
- Print on its side as supplied: strongest layer direction, no supports
- PLA or PETG, 0.2 mm layers, 3 walls, 15–20 % infill
Blender check (live Blender 5.2.1)
| File | Size (mm) | Triangles | Non-manifold | Open edges | Normals | Shells | Overhang >45° |
|---|---|---|---|---|---|---|---|
phone_stand_55deg | 89.46 × 110.93 × 72 | 1,312 | 0 | 0 | outward ✔ | 1 | 1.4% |
phone_stand_65deg | 80 × 118.69 × 72 | 1,316 | 0 | 0 | outward ✔ | 1 | 1.6% |
phone_stand_75deg | 80 × 123.76 × 72 | 1,300 | 0 | 0 | outward ✔ | 1 | 1.7% |
tablet_stand_60deg | 110 × 150.41 × 130 | 1,316 | 0 | 0 | outward ✔ | 1 | 0.7% |
tablet_stand_70deg | 110 × 159.57 × 130 | 1,308 | 0 | 0 | outward ✔ | 1 | 0.8% |
Fit & stability tests
| Part | Test | Result |
|---|---|---|
phone_stand_55deg | 12 mm device (phone, 165 mm tall) in slot | 0 intersections ✔ |
phone_stand_55deg | USB-C plug + 24 mm strain relief below the port | 0 intersections ✔ |
phone_stand_55deg | centre of gravity inside footprint | margin 25.3 mm ✔ |
phone_stand_65deg | 12 mm device (phone, 165 mm tall) in slot | 0 intersections ✔ |
phone_stand_65deg | USB-C plug + 24 mm strain relief below the port | 0 intersections ✔ |
phone_stand_65deg | centre of gravity inside footprint | margin 28.2 mm ✔ |
phone_stand_75deg | 12 mm device (phone, 165 mm tall) in slot | 0 intersections ✔ |
phone_stand_75deg | USB-C plug + 24 mm strain relief below the port | 0 intersections ✔ |
phone_stand_75deg | centre of gravity inside footprint | margin 42.0 mm ✔ |
tablet_stand_60deg | 12 mm device (tablet, 250 mm tall) in slot | 0 intersections ✔ |
tablet_stand_60deg | USB-C plug + 24 mm strain relief below the port | 0 intersections ✔ |
tablet_stand_60deg | centre of gravity inside footprint | margin 29.6 mm ✔ |
tablet_stand_70deg | 12 mm device (tablet, 250 mm tall) in slot | 0 intersections ✔ |
tablet_stand_70deg | USB-C plug + 24 mm strain relief below the port | 0 intersections ✔ |
tablet_stand_70deg | centre of gravity inside footprint | margin 49.6 mm ✔ |
Overhang shown is the short bridging over the cable tunnel and bumper recesses in the side-printing orientation, no supports needed. Not yet physically test-printed.
Technical details
- Formats
- STL, 3MF
- Software
- Bambu Studio, PrusaSlicer, OrcaSlicer, Cura
- Provenance
- Procedural
- AI training
- prohibited
- Watertight
- Yes
- Manifold
- Yes
- Print tested by creator
- No
- Printer type
- fdm
- Supports required
- none
- Dimensions (W×D×H mm)
- Phone stands 72 x 80-89 x 111-124 (W x D x H); tablet stands 130 x 110 x 150-160
- Recommended print settings
- PLA/PETG, 0.2 mm layers, 3 walls, 15-20% infill, print on the side as supplied, no supports
Reviews
Own this asset? Sign in to review it.
No reviews yet. Owners can share how the asset worked for them.
Questions & comments
Sign in to ask the creator a question.
No questions yet. Ask about formats, compatibility or licensing.