Skip to content
AssetLoom
Interactive 3D preview (reduced-detail model, 3,272 triangles · 12 × 22 × 18 cm). The downloadable files are the full-resolution originals.

Description

A set of printable desktop drawers that stack into one rigid tower. Two locating bumps on each case top sit in sockets under the case above, so stacked cases cannot slide front, back or sideways when you open a drawer. Two printed dovetail keys slide in from the back and stop the cases lifting apart, so you can pick up the whole tower by the top case. All parts print with no supports.

What's included (16 print files, STL + 3MF, in print orientation)

  • Cases 120 x 150 mm in 40, 60 and 80 mm heights. Mix them in any order
  • Drawers for each height, with a finger notch and a front panel that covers the case side and top edges
  • Dividers for each height. Each drawer has 5 rib slots, so you choose the compartments
  • Lock keys in 3 fits: snug (0.15 mm per flank), standard (0.25) and loose (0.35), marked with 1, 2 or 3 dimples
  • Fit test kit: a small groove block (print two) and three short keys, so you can find your fit in about 10 minutes before printing full-length keys
  • The .blend file and the Python generator: change the width, depth, heights, walls or clearances and rebuild every part

How it goes together

Slide a drawer into its case. To stack, set one case on another so its bumps drop into the sockets above, then push two keys in from the back until they stop about 3 mm short of the front. Each key leaves a 3.5 mm grip outside the back, so you can pull it out to take the tower apart.

Print settings

  • PLA or PETG, 0.4 mm nozzle, 0.2 mm layers, no supports, no scaling
  • Cases print standing on their back with the opening up (needs 155 mm build height; use a 5 mm brim for the 40 mm case); drawers print open side up; dividers and keys print flat. Every part fits a 180 x 180 mm bed
  • Cases: 2 walls, 15 % infill, roughly 125 / 145 / 165 g of PLA each. Drawers roughly 65 / 90 / 115 g. Weights are estimates; check your slicer

Please note

Clearances were checked in software between every pair of mating parts (drawer 0.5 mm each side and 0.8 mm at the top, dividers 0.2 mm, bumps 0.3 mm, keys as above), but the set has not yet been test-printed by us, which is why the fit test kit is included. Drawers have no pull-out stop. The batteries, pencils and erasers in the previews are props and are not included.

Technical details

Formats
STL, 3MF, BLEND
Software
Bambu Studio, PrusaSlicer, OrcaSlicer, Cura, Blender
Provenance
Procedural
AI training
prohibited
Watertight
Yes
Manifold
Yes
Print tested by creator
No
Printer type
fdm
Supports required
none
Dimensions (W×D×H mm)
Cases 120 x 150 x 40 / 60 / 80 (plus 1.5 mm locating bumps); drawers 119 x 150.5 x 35.9 / 55.9 / 75.9; dividers 111.2 x 29.3-69.3 x 1.6; keys 150.5 x 6.1-6.5 x 3.6
Recommended print settings
PLA or PETG, 0.4 mm nozzle, 0.2 mm layers, 2 walls and 15% infill for cases and drawers (3 walls or 100% for keys and dividers), 5 mm brim for the 40 mm case, print as supplied, no supports, no scaling, slicer XY compensation 0; print the fit test kit first

Version history

Latest version 1.0.1, released .

  1. 1.0.1

    File tidy-up: cleaner file metadata and notes; no changes to the models.

  2. 1.0.0

Reviews

Own this asset? Sign in to review it.

No reviews yet. Owners can share how the asset worked for them.

    Questions & comments

    Sign in to ask the creator a question.

    No questions yet. Ask about formats, compatibility or licensing.